Arduino Uno Rev.3 (ATmega328P MCU)

Arduino UNO R3

5609 views





















































  • Microcontroller


ATmega328


  • Operating Voltage


5V


  • Input Voltage (recommended)


7-12V


  • Input Voltage (limits)


6-20V


  • Digital I/O Pins


14 (of which 6 provide PWM output)


  • Analog Input Pins


6


  • DC Current per I/O Pin


40 mA


  • DC Current for 3.3V Pin


50 mA


  • Flash Memory


32 KB (ATmega328) of which 0.5 KB used by bootloader


  • SRAM


2 KB (ATmega328)


  • EEPROM


1 KB (ATmega328)


  • Clock Speed


16 MHz
Features
  • Microcontroller
ATmega328
  • Operating Voltage
5V
  • Input Voltage (recommended)
7-12V
  • Input Voltage (limits)
6-20V
  • Digital I/O Pins
14 (of which 6 provide PWM output)
  • Analog Input Pins
6
  • DC Current per I/O Pin
40 mA
  • DC Current for 3.3V Pin
50 mA
  • Flash Memory
32 KB (ATmega328) of which 0.5 KB used by bootloader
  • SRAM
2 KB (ATmega328)
  • EEPROM
1 KB (ATmega328)
  • Clock Speed
16 MHz
View detail


The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.


The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features theAtmega16U2 (Atmega8U2 up to version R2) programmed as a USB-to-serial converter.
Revision 2 of the Uno board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode.
Revision 3 of the board has the following new features:
  • 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Arduino Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes.
  • Stronger RESET circuit.
  • Atmega 16U2 replace the 8U2.
"Uno" means one in Italian and is named to mark the upcoming release of Arduino 1.0. The Uno and version 1.0 will be the reference versions of Arduino, moving forward. The Uno is the latest in a series of USB Arduino boards, and the reference model for the Arduino platform; for a comparison with previous versions, see the index of Arduino boards.

Microcontroller ATmega328
Operating Voltage 5V
Input Voltage (recommended) 7-12V
Input Voltage (limits) 6-20V
Digital I/O Pins 14 (of which 6 provide PWM output)
Analog Input Pins 6
DC Current per I/O Pin 40 mA
DC Current for 3.3V Pin 50 mA
Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM 2 KB (ATmega328)
EEPROM 1 KB (ATmega328)
Clock Speed 16 MHz

 

  

Price list

Quantity Unit Price Extended Price
1 215,000đ 215,000đ
10 210,000đ 2,100,000đ
50 205,000đ 10,250,000đ
100 200,000đ 20,000,000đ
Đang cập nhật.
Please enter correct your email
Content is your comment!
Content is too short to!
Comment is too long!
You can not continually write comments!

Related products